IS 5244 : 1991 ( Reaffirmed 2010 ) Indian Standard SAFE DEPOSIT LOCKER CABINETS -- SPECIFICATION ( Second Revision ) UDC 683.342 © BIS 1991 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI 110002 September 1991 Price Group 3 Safes Sectional Committee, HMD 24 FOREWORD This Indian Standard ( Second Revision ) was adopted by the Bureau of Indian Standards, after the draft finalized by the Safes Sectional Committee had been approved by the Heavy Mechanical Engineering Division Council. This Indian Standard was first published in 1969 and revised in 1987. The standard is being revised to bring it in line with the latest developments in the field. In this revision tests and performance requirements for safe deposit locker cabinets have been specified. Security equipment play a vital role in the safety of cash, jewellery, important documents, etc, in establishments such as banks, hotels, commercial organizations, shops, etc. Safe deposit locker cabinets are designed for convenient deposit and storage of precious articles, documents and the like of a lessee which might otherwise get an access by undesirable persons during an attempted robbery. In reporting the results of a test or analysis made in accordance with this standard, if the final value, observed or calculated is to be rounded off, it shall be done in accordance with IS 2 : 1960 'Rules for rounding off numerical values (revised)'. AMENDMENT NO. 4 SEPTEMBER 2010 TO IS 5244 1991 SAFE DEPOSIT LOCKER CABINETS ­ SPECIFICATION (Second Revision ) (Amendment No. 3, clause 4.7, third line) -Substitute '0.7' for '0.8'. (Amendment No. 3, clause 4.7, fourth line) -Substitute 'AC 5' for 'AC 15'. (Amendment No. 3, clause 4.7, fifth line)-Substitute '0.7' for '0.8'. [ Page 4, clause 7.5 (see also Amendment No. 1)]-Add the following matter at the end: 'Any other paint system like polyurethane paint, powder coating, etc, mutually agreed to between the purchaser and the supplier may also be applied.' (Page 4, clause 7.6, fourth line) -Substitute '0.05' for '0.1'. (ME 24) Reprography Unit, BIS, New Delhi, India AMENDMENT NO. 3 SEPTEMBER 2003 TO IS 5244 : 1991 SAFE DEPOSIT LOCKER CABINETS -- SPECIFICATION ( Second Revision ) ( Page 1, clause 2 ) -- Delete 'IS 1570 (Part 5) : 1985 Schedules for wrought steels : Part 5 Stainless and heat resisting steels (second revision)' and add 'IS 1868 : 1996 Anodic coatings o aluminium and its alloys -- Specification (third revision)' at appropriate place. ( Page 1, clause 2 ) -- Insert the following after IS 2932 : 1974: 'IS No. 5986 : 2002 Title Hot rolled steel products for structural forming and flanging purposes -- Specification (second revision) 6603 : 2001 Stainless steel bars and flats -- Specification (first revision) [ Page 1, clauses 4.1, 4.2, 4.3, 4.4, 4.5 and 4.6 (see also Amendments No. 1 and 2) ] -- Substitute 'IS 2062 : 1999 or IS 5986 : 2002' for 'IS 2062 : 1992'. ( Page 1, clause 4.7 ) -- Substitute the following for the existing: '4.7 The door shall be covered with stainless steel fronts conforming to Designation X04Cr19Ni9 or X07Crl8Ni9 of IS 6603 : 2001. Alternatively the doors may have anodized aluminium cladding of nominal 0.8 mm thickness minimum, anodized to Grade AC15 as per IS 1868 : 1996 or mild steel sheet of nominal 0.8 mm thickness minimum, powder coated to have corrosion resistance equivalent to anodized aluminium.' (Page 4, clause 7.2 ) -- Substitue the following for the existing matter: 'The gap between the shutter and doorplate shall not be more than 1 mm, if there is a direct thorough passage. Wherever there is no direct thorough passage the gap can be maximum 1.5 mm.' (ME 24) Reprography Unit, BIS, New Delhi, India AMENDMENT NO. 2 MAY 1996 TO IS 5244 : 1991 SAFE DEPOSIT LOCKER CABINETS -- SPECIFICATION ( Second Revision ) [ Page 1, clause 2 ( see also Amendment No. 1 ) ] -- Insert the following matter after IS 419 :1967: 'IS 513 : 1994 IS 1079 : 1994 Cold rolled low carbon steel sheets and strips (fourth revision) Hot rolled carbon steel sheets and strips (fifth revision )' [ Page 1, clause 4.3 ( see also Amendment No. 1 ) ] -- Substitute the following for the existing matter ' 4.3 The partition and the shelves shall be of minimum 2 mm thick steel plates conforming to IS 2062 : 1992 or IS 513 : 1994 or IS 1079 :1994.' [ Page 1, clause 4.4 ( see also Amendment No. 1 ) ] -- Substitute the following for the existing matter ' 4.4 The bottom shall be of minimum 3.15 mm thick steel plates conforming to IS 2062 : 1992 or minimum 2 mm thick plate with stiffener reinforcement of 2 mm thickness conforming to IS 2062 : 1992 or IS 513 : 1994 or IS 1079 : 1994.' (HMD 24) Reprography Unit, BIS, New Delhi, India AMENDMENT NO. 1 AUGUST 1994 TO IS 5244 : 1991 SAFE DEPOSIT LOCKER CABINETS -- SPECIFICATION ( Second Revision ) [ Page 1, clause 2, IS 226 : 1975, IS 814 (Part 1): 1974 and IS 814 (Part 2): 1974] -- Delete. (Page 1, clause 2) -- Insert the following matter after IS 419 : 1967: '814:1991 Covered electrodes for manual arc welding of carbon and carbon manganese steel (fifth revision)' ( Page 1, clause 2 ) -- Substitute the following for IS 2062 : 1984 and IS 2074: 1979: 'IS 2062 : 1992 IS 2074 :1992 Steel for general structural purposes (fourth revision) Ready mixed paint, air drying, red oxide-zinc chrome, priming (second revision)' ( Page 1, clauses 4.1, 4.2, 4.3, 4.4, 4.5 and 4.6 ) -- Substitute 'IS 2062 : 1992' for 'IS 2062 : 1984 or IS 226 : 1975'. ( Page 1, clause 4.8 ) -- Substitute 'IS 814 : 1991' for 'IS 814 (Part 1) : 1974 or IS 814 (Part 2): 1974'. ( Page 1, clause 4.10, second line ) -- Substitute 'IS 2074 : 1992' for 'IS 2074 : 1979'. ( Page 4, clause 7.5, fourth line ) -- Substitute 'IS 2074 : 1992' for 'IS 2074:1979'. (HMD 24) Reprography Unit, BIS, New Delhi, India IS 5244 : 1991 Indian Standard SAFE DEPOSIT LOCKER CABINETS -- SPECIFICATION ( Second Revision ) 1 SCOPE This standard lays down the requirements regarding materials and details of construction of safe deposit locker cabinets which afford security to precious articles, documents and the like of a lessee in as much as undesirable persons not getting access to their vaults by violence or stealth. 2 REFERENCES The following Indian Standards are adjuncts to this standard: IS No. 226:1975 necessary 4 MATERIAL 4.1 The two sides and top of the locker cabinets shall be of 5 mm thick steel plates conforming to IS 2062 : 1984 or IS 226 : 1975. 4.2 The back of the locker cabinets shall be of 5 mm thick steel plates conforming to IS 2062 : 1984 or IS 226 : 1975. 4.3 The partitions and the shelves shall be of minimum 2 mm thick steel plates conforming to IS 2062 : 1984 or IS 226 : 1975. 4.4 The bottom shall be of minimum 315 mm thick steel plates conforming to IS 2062 : 1984 or IS 226 : 1975 or minimum 2 mm thick with stiffener reinforcement of 2 mm conforming to IS 2062 : 1984 or IS 226 : 1975. Title Structural steel (standard quality) (first revision ) 419 : 1967 Putty for use on window 4.5 The door shall be of 10 mm thick steel frames (first revision) plates conforming to IS 2062 : 1984 or IS 226 : 814 (Part 1) : Covered electrodes for metal 1975. The hinge arrangement shall be such that 1974 arc welding of structural steels: it shall provide sufficient resistance against Part 1 For welding products tempering attacks of common hand tools. If the other than sheets (fourth hinges of locker units in a vertical row has a canteens bar hinge, the arrangement of fixing bar revision) 814 Covered electrodes for metal shall be such as to prevent lifting of the bar (Part 2 ) : 1974 arc welding of structural easily by cutting top or bottom part of the hinge or being bent by being pulled forward with a steels : Part 1 For welding picking tool. sheets (fourth revision) 1365 : 1978 Slotted countersunk head 4.6 The shelves shall be reinforced at front with a minimum of 5 mm thick steel flats conforming screws ( third revision ) 1570 Schedules for wrought steels: to IS 2062 : 1984 or IS 226 : 1975. (Part 5 ) : 1985 Part 5 Stainless and heat- 4.7 The doors shall be covered with stainless resisting steels (second steel fronts conforming to Designation 04Cr19Ni9 revision ) or 07Crl9Ni9 of IS 1570 ( Part 5 ) : 1985. Alter2062 : 1984 Weldable structural steel natively the doors may have anodized aluminium ( third revision ) cladding of minimum 0.8 mm thick anodized to 2074 : 1979 Ready mixed paint, air drying, 15 microns or mild steel sheet of 0.8 mm thickred oxide zinc chrome, priming ness powder coated to have corrosion resistance (first revision) equivalent to anodized aluminium. 2932 : 1974 Enamel, synthetic, exterior (a) under coating, (b) finish- 4.8 Electrodes for welding shall conform to IS 814 (Part 1) : 1974 or IS 814 (Part 2) : 1974. ing (first revision) 3 TYPES 4.9 Screws shall conform to IS 1365 : 1978. 3.1 Safe deposit locker cabinets shall be of the 4.10 Primer of red oxide-zinc chromate conformfollowing types: ing to IS 2074 : 1979 shall be used. Putty shall a) Type 1 -- Containing 75 lockers, conform to ISI specification, suitable for leveling surface of metal before painting. b) Type 1A -- Containing 90 lockers, c) Type 2 -- Containing 52 lockers, 4.11 Undercoating shall conform to IS 2932 : d) Type 2A -- Containing 51 lockers, and 1974. e) Type 3 -- Containing 32 lockers. 5 SIZES 3.2 Any other configuration may be given subject to agreement between the manufacturer and the The dimensions of safe deposit lockers shall be as given in Fig. 1 to 5. purchaser. 1 IS 5244 : 1991 Lockers Minimum Inside Measurements mm Size A 2A 4A High 115 115 266 Wide 149 329 329 Deep 470 470 470 No. 66 6 3 Size : 2 000 mm high × 1 100 mm wide × 575 mm deep ( outside). Tolerance : ± 25 mm. FIG. 1 SAFE DEPOSIT LOCKER CABINET TYPE 1, 75 LOCKERS 6 DESIGN AND MANUFACTURE 6.1 The construction of safe deposit locker cabinet shall be such that it provides maximum security to the lessee. Lockers shall be secured with first class unpickable dual control key-lock. They shall be selflocking so that the custodian does not have to re-lock the locker with his (custodian's) key after the lessee has locked it. The mechanism of the lock shall be such that the lessee shall not be able to withdraw his key unless the locker has been re-locked fully. Once 2 the lessee has locked the locker, the same cannot be opened unless the custodian turns in his key to take off his control. No key of one lock shall apply to any other lock except its own. The lessee's as well as the custodian's keys shall be made of stainless steel. 6.2 The locks shall be interchangeable so that when a locker is vacated by a lessee, the lock may be and should be immediately transferred to another locker and vice versa. IS 5244 : 1991 Lockers Minimum Inside Measurements mm Size A High 115 Wide 149 Deep 470 No. 90 Size : 2 000 mm high × 1 100 mm wide × 575 mm deep ( outside ). FIG. 2 Tolerance : ± 25 mm. SAFE DEPOSIT LOCKER CABINET TYPE 1A, 90 LOCKERS 6.3 Provision shall be made to fit on the inside of the locker door another strong and unpickable lock of the lessee if so desired by the lessee. Third key hole of the renter's lock, when the lock is not fitted will be protected by a plate or by secure plug, making the inside of the locker inaccessible to access from the outside. An outside pad locking arrangement or hasp shall also be provided. 6.4 The lock and the shutter arrangement shall be such that the lever of the lock projecting into locker or the locking hole, as the case may be, shall have sufficient protection against tampering with crow bar or other hand tools. 6.5 Lever of lock shall be strong enough in both the directions of its section ( that is, Ixx and IYY ) to provide resistance against bending. 6.6 The lever when lock is in locked position, shall have depth of engagement of not less than 5 mm. 7 WORKMANSHIP AND FINISH 7.1 All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale preferably by sand blasting or by normal pickling process. 3 IS 5244 : 1991 Lockers Minimum Inside Measurements mm Size B 2B 4B High 148 148 314 Wide 184 401 401 Deep 470 470 470 No. 48 2 2 Size : 2000 mm high × 1 100 mm wide × 575 mm deep (outside ). Tolerance : ± 25 mm. FIG. 3 SAFE DEPOSIT LOCKER CABINET TYPE 2, 52 LOCKERS 7.2 Tolerance The gap between the shutter and frame shall not be more than 1.0 mm. The rebate cover shall be minimum 8 mm. 7.3 Welded joints shall be free from slags. welding 7.6 Finish shall be smooth, uniformly applied and free from visible defects. It shall be smooth and shall not readily chip or flake. The dry film thickness shall not be less than 0.1 mm and shall be polished to bring out lustre. 8 TESTING 7.4 All surfaces shall be phosphatized or shot/ sand blasted before application of rust proof primer. 8.1 The locker unit shall be tested for its performance against burglarious attacks with common hand tools such as spanners, pliers, chisels, punches, hammers (not exceeding 1 kg in mass), crow bars (maximum 500 mm in length and 7.5 Putty conforming to IS 419 : 1967 shall be 15 mm in diameter) and screw drivers. The applied to all surface requiring filling. Two coats locker units shall be able to withstand such of undercoat and final coat paint conforming to attacks successfully for a period of not less than 15 minutes. IS 2074 : 1979 shall be applied. 4 IS 5244 : 1991 Lockers Minimum Inside Measurements mm Size B 2B 4B 2B1 High 148 148 314 314 Wide 184 401 401 184 Deep 470 470 470 470 No. 46 2 2 1 Size : 2 000 mm high × 1 100 mm wide × 575 mm deep ( outside ). Tolerance : ± 25 mm. FIG. 4 SAFE DEPOSIT LOCKER CABINET TYPE 2A, 51 LOCKERS 5 IS 5244 : 1991 Lockers Minimum Inside Measurements mm Size D 2D 4D High 178 178 394 Wide 238 506 506 Deep 470 470 470 No. 28 2 2 Size : 2 000 mm high × 1 100 mm wide × 575 mm deep ( outside ). Tolerance : ± 25 mm. FIG. 5 SAFE DEPOSIT LOCKER CABINET TYPE 3, 32 LOCKERS 8.2 Each locker unit shall be tested to ensure that the customer's key does not come out unless the shutter is completely closed and the lock is fully locked. 9 MARKING 9.1 All the safe deposit locker cabinets shall be marked with the manufacturer's name or trademark, the type and year of manufacture. 9.1.1 Certification Marking Safe deposit locker cabinets may also be marked with the Standard Mark. 9.2 The lockers shall be serially numbered and marked on the outside of locker doors by the manufacturer as desired by the customer. 9.3 Marking on Keys The keys shall be marked with an identification number which shall not be the same as the serial number of the corresponding locker. 10 INSPECTION The purchaser or his authorized representative shall normally have free access to inspect the safe deposit locker cabinets at various stages of manufacture. 11 PACKING All the component parts shall be packed in such a way that no damage is caused to them during transit. The key shall be sealed in a box and dispatched separately to the purchaser in person. 6 Standard Mark The use of the Standard Mark is governed by the provisions of the Bureau of Indian Standards Act, 1986 and the Rules and Regulations made thereunder. The Standard Mark on products covered by an Indian Standard conveys the assurance that they have been produced to comply with the requirements of that standard under a well denned system of inspection, testing and quality control which is devised and supervised by BIS and operated by the producer. Standard marked products are also continuously checked by BIS for conformity to that standard as a further safeguard. Details of conditions under which a licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards. Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country. Copyright BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Enquires relating to copyright be addressed to the Director ( Publications ), BIS. Revision of Indian Standards Indian Standards are reviewed periodically and revised, when necessary and amendments, if any, are issued from time to time. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition. Comments on this Indian Standard may be sent to BIS giving the following reference : Doc : No. HMD 24 ( 0036 ) Amendments Issued Since Publication Amend No. Date of Issue Text Affected BUREAU OF INDIAN STANDARDS Headquarters: Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telephones : 331 01 31, 331 13 75 Regional Offices: Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg NEW DELHI 110002 Eastern : 1/14 C. I. T. Scheme VII M, V. I. P. Road, Maniktola CALCUTTA 700054 Northern : SCO 445-446, Sector 35-C, CHANDIGARH 160036 Southern : C. I. T. Campus, IV Cross Road, MADRAS 600113 Western : Manakalaya, E9 MIDC, Marol, Andheri ( East ) BOMBAY 400093 Telegrams : Manaksanstha (Common to all Offices ) Telephone 331 01 31 331 13 75 37 86 62 53 38 43 235 02 16 6 32 92 95 Branches : AHMADABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD. GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. PATNA. SRINAGAR. THIRUVANANTHAPURAM. Printed at Printrade, New Delhi, India